Embedded and IoT Lab Setup
- Low cost solutions
- High end embedded board for processing
- New upcoming connectivity technology
- End to end solution
- Consisting of sensors, embedded boards, connectivity solutions, gateways, cloud services along with required training and support for making it a success
- Experienced industry experts to support for training
IoT Trainer Kit
- Quad-core ARM Cortex-A53 (Armv8-A architecture)
- Up to 1.2GHz Clock speed, Broadcom Video Core IV
- 1GB LPDDR2 (900 MHz), MicroSDHC slot for onboard storage
- Multiple communication interfaces
- On board Sensors: Accelerometer, Gyroscope, Temperature, Humidity, Pressure
- User interfaces: 3×3 channel relay, 3 RGB LED, 2 Push button, Buzzer, OLED display
- Ports: UART, SPI, I2C, 8 Analog I/O, 31 GPIOs, 4 USB 2.0 port, 3.5mm analog audio-video jack, 6x5V Power supply, 5×3.3V Power supply, HDMI output, CSI, DSI
- External Sensors: PIR, Ultrasonic, GAS, Air Quality, IR, Fire, Light, Flex, Heartbeat, vibration sensor, servo motor, Soil Moisture sensor, Rain sensor
LoRa IoT Development Kit
- Necessary hardware to start with IoT projects for studying, evaluating.
- Learning the Arduino code and some other mcu knowledge.
- Learning how to use the commonly used sensors.
- Learning the basic knowledge of Linux.
- Learning the basic construction of IoT and how it works.
- Learning the LoRa wireless technology.
- Learning how to build a LoRa network.
- Learning how to use your sensor network to communicate with different IoT servers
Deployable Water Proof LoRa Sensor Node
- STM32L072CZT6 MCU along with SX1276/78 LoRa Wireless Modem
- Pre-load with ISP bootloader
- I2C,LPUSART1,USB,18 x Digital I/Os
- 2 x 12bit ADC & 1 x 12bit DAC
- MCU wake up by UART or Interrupt
- Preamble detection, Baud rate configurable
- LoRaWAN 1.0.2 Specification
- Software base on STM32Cube HAL drivers
- Open source hardware / software
- Available Band:433/868/915/920 Mhz
- IP66 Waterproof Enclosure
- Ultra Low Power consumption
- AT Commands to setup parameters
- 4000mAh Battery for Long term use
Single Channel Indoor LoRa Gateway
- Open Source OpenWrt system
- Low power consumption
- Firmware upgrade via Web
- Software upgradable via network
- Auto-Provisioning
- Built-in web server
- Managed by Web GUI, SSH via LAN or WiFi
- Support WiFi AP, Client or Ad-Hoc(Mesh) mode
- Internet connection via LAN, WiFi, 3G or 4G
- Failsafe design provides robustly system
- Arduino IDE compatible. Easy to program.
- LoRa band available at 433/868/915/920 Mhz
- Max range in LoRa : 5 ~ 10km
Dual Channel Indoor LoRa Gateway
- Open Source OpenWrt system
- Low power consumption
- Firmware upgrade via Web
- Software upgradable via network
- Flexible protocol to connect to IoT servers
- Auto-Provisioning, Built-in web server
- Managed by Web GUI, SSH via LAN or WiFi
- Internet connection via LAN, WiFi, 3G or 4G
- Failsafe design provides robustly system
- 2 x SX1276/SX1278 LoRa modules
- Full–duplex LoRa transceiver with 2 receive channels and 1 transmit channel
- Limited support in LoRaWAN/ Support Private LoRa protocol
- Support upto 300 nodes
- LoRa band available at 433/868/915/920 Mhz
- Max range in LoRa: 5~10 km. Density Area:>500m,
Single Channel Outdoor Gateway
- Open Source OpenWrt system
- Low power consumption
- Firmware upgrade via Web
- Software upgradable via network
- Auto-Provisioning, Built-in web server
- Managed by Web GUI, SSH via LAN or WiFi
- Support WiFi AP, Client or Ad-Hoc(Mesh) mode
- Internet connection via LAN, WiFi, 3G or 4G
- Failsafe design provides robustly system
- Arduino IDE compatible. Easy to program.
- LoRa band available at 433/868/915/920 Mhz
- Max range in LoRa : 5 ~ 10km
- SMA connector for external LoRa antenna
- 12dBi WiFi directional antenna
- Passive PoE Interface
- Weather proof enclosure
Dual Channel Outdoor LoRa Gateway
- Open Source OpenWrt system
- Low power consumption
- Firmware upgrade via Web
- Software upgradable via network
- Flexible protocol to connect to IoT servers
- Auto-Provisioning, Built-in web server
- Managed by Web GUI, SSH via LAN or WiFi
- Internet connection via LAN, WiFi, 3G or 4G
- Failsafe design provides robustly system
- 2 x SX1276/SX1278 LoRa modules
- Full–duplex LoRa transceiver
- Two receive channels, and one transmit channel
- Limited support in LoRaWAN/ Support Private LoRa protocol
- Support upto 300 nodes
- LoRa band available at 433/868/915/920 Mhz
- Max range in LoRa: 5~10 km. Density Area:>500m
LoRa Shield for Arduino
- Compatible with 3.3v or 5v I/O Arduino Board.
- Frequency Band: 915MHz/868 MHZ/433 MHZ (Pre-configure in factory)
- Low power consumption
- Compatible with Arduino Leonardo, Uno, Mega, DUE
- External Antenna via I-Pex connector
LoRa GPS Shield for Arduino
- Frequency Band: 868 MHZ/433 MHZ/915 MHZ(Pre-configure in factory)
- Low power consumptionCompatible with Arduino Leonardo, Uno, Mega,Due etc.
- LoRa™ Modem with FSK, GFSK, MSK, GMSK, LoRa™and OOK modulation
- Preamble detection, Baud rate configurable
- Built-in temperature sensor and low battery indicator
- Excellent blocking immunity
- Automatic RF Sense and CAD with ultra-fast AFC
- Support DGPS, SBAS(WAAS/EGNOS/MSAS/GAGAN)
- GPS automatic switching between internal patch antenna and external active antenna
- PPS VS. NMEA can be used in time service
- Support SDK command, Built-in LNA for better sensitivity
- EASY™, advanced AGPS technology without external memory
- AlwaysLocate™, an intelligent controller of periodic mode
- GPS FLP mode, about 50% power consumption of normal mode
- GPS support short circuit protection and antenna detection
LoRa GPS HAT for Raspberry Pi
- Frequency Band: 868 MHZ/433 MHZ/915 MHZ(Pre-configure in factory)
- Low power consumption
- Compatible with Raspberry Pi 2 Model B/Raspberry Pi 3.
- LoRa™ Modem with FSK, GFSK, MSK, GMSK, LoRa™and OOK modulation
- Preamble detection, Baud rate configurable
- Built-in temperature sensor and low battery indicator
- Excellent blocking immunity
- Automatic RF Sense and CAD with ultra-fast AFC
- Support DGPS, SBAS(WAAS/EGNOS/MSAS/GAGAN)
- GPS automatic switching between internal patch antenna and external active antenna
- PPS VS. NMEA can be used in time service
- Support SDK command, Built-in LNA for better sensitivity
- EASY™, advanced AGPS technology without external memory
- AlwaysLocate™, an intelligent controller of periodic mode
- GPS FLP mode, about 50% power consumption of normal mode
- GPS support short circuit protection and antenna detection
LoRaST IoT Module
- STM32L072CZT6 MCU along with SX1276/78 LoRa Wireless Modem
- Pre-load with ISP bootloader
- I2S,I2C,LPUSART1,SPI2,USB
- 22 x Digital I/Os, 3 x 12bit ADC; 1 x 12bit DAC
- MCU wake up by UART or Interrupt
- LoRa™ Modem
- Preamble detection, Baud rate configurable
- LoRaWAN 1.0.2 Specification
- Software base on STM32Cube HAL drivers
- Open source hardware / software
- Available Band:433/868/915/920 Mhz
- External Antenna via I-Pex 4 connector
- Ultra Low Power consumption
- AT Commands to setup parameters
- Industrial standard M.2 (NGFF) interface
LoRa Mini Development Board
- Base on ATmega328P + SX1276/78
- Frequency Band: 868 MHZ/433 MHZ/915 MHZ(Pre-configure in factory)
- LoRa™ Modem
- FSK, GFSK, MSK, GMSK, LoRa™and OOK modulation
- Pre-load with Arduino Bootloader
- Able to program via Arduino IDE
LoRa Mini Module
- Base on ATmega328P + SX1276/78
- Frequency Band: 868 MHZ/433 MHZ/915 MHZ(Pre-configure in factory)
- LoRa™ Modem
- FSK, GFSK, MSK, GMSK, LoRa™and OOK modulation
- Pre-load with Arduino Bootloader
- Able to program via Arduino IDE
LoRa Mini Program Utility
- Program LoRa Mini without soldering it
- Program LoRa Mini with USB cable and Arduino IDE
- Power on/off button
- Reset button
LoRa I/O Controller
- STM32L072CZT6 MCU
- SX1276/78 LoRa Wireless Chip
- LoRaWAN Class A & Class C protocol
- Optional Customized LoRa Protocol
- Bands: CN470/EU433/KR920/US915/EU868/AS923/AU915
- AT Commands to change parameters
LoRa Bee Module
- Frequency Band: 868 MHZ/433 MHZ/915 MHZ(Pre-configure in factory)
- LoRa™ Modem
- FSK, GFSK, MSK, GMSK, LoRa™and OOK modulation
- XBee form factory
Indoor LoRaWAN Pico Gateway
- Open Source OpenWrt system
- Managed by Web GUI, SSH via LAN or WiFi
- Emulates 49x LoRa demodulators
- LoRaWAN Gateway
- SX1276 base seperate TX path
- 10 programmable parallel demodulation paths
Skill Development Program
- Faculty development programs
- Workshops for students and faculties
- 35 different courses available
- Few courses are Embedded, NI LabVIEW, NI DAQ cards, Robotics etc
- Training conducted by experienced industry experts
Sensors
- All kind of chemical, physics, medical etc sensors available
- Like PIR sensor, ultrasonic sensor, gas sensor, air quality sensor, IR sensor, fire sensor, light sensor, flex sensor, heartbeat, vibration sensor, servo motor, soil moisture sensor, rain sensor
- Industry experts on various sensors technology to help you build your systems
Smart CO2 LoRa Sensor
The purpose of installing Smart CO2 LoRa based Sensor on the premise is to:
- Monitor COVID-19 relevant CO2 in Rooms
- Air Quality (Temperature & Humidity)
- Direct Alert on Device (Buzzer and LED)
- Notify Responders
- Communicate Emergency
- Trend Indication and Data Analysis