Prodct - embedded &iot

Embedded and IoT Lab Setup

  • Low cost solutions
  • High end embedded board for processing
  • New upcoming connectivity technology
  • End to end solution
  • Consisting of sensors, embedded boards, connectivity solutions, gateways, cloud services along with required training and support for making it a success
  • Experienced industry experts to support for training 

IoT Trainer Kit

  •  Quad-core ARM Cortex-A53 (Armv8-A architecture)
  • Up to 1.2GHz Clock speed, Broadcom Video Core IV
  • 1GB LPDDR2 (900 MHz), MicroSDHC slot for onboard storage
  • Multiple communication interfaces
  • On board Sensors: Accelerometer, Gyroscope, Temperature, Humidity, Pressure
  • User interfaces: 3×3 channel relay, 3 RGB LED, 2 Push button, Buzzer, OLED display
  • Ports: UART, SPI, I2C, 8 Analog I/O, 31 GPIOs, 4 USB 2.0 port, 3.5mm analog audio-video jack, 6x5V Power supply, 5×3.3V Power supply, HDMI output, CSI, DSI
  • External Sensors: PIR, Ultrasonic, GAS, Air Quality, IR, Fire, Light, Flex, Heartbeat, vibration sensor, servo motor, Soil Moisture sensor, Rain sensor
LoRa_IoT_Kit_10

LoRa IoT Development Kit

  • Necessary hardware to start with IoT projects for studying, evaluating.
  • Learning the Arduino code and some other mcu knowledge.
  • Learning how to use the commonly used sensors.
  • Learning the basic knowledge of Linux.
  • Learning the basic construction of IoT and how it works.
  • Learning the LoRa wireless technology.
  • Learning how to build a LoRa network.
  • Learning how to use your sensor network to communicate with different IoT servers

Deployable Water Proof LoRa Sensor Node

  • STM32L072CZT6 MCU along with SX1276/78 LoRa Wireless Modem
  • Pre-load with ISP bootloader
  • I2C,LPUSART1,USB,18 x Digital I/Os
  • 2 x 12bit ADC & 1 x 12bit DAC
  • MCU wake up by UART or Interrupt
  • Preamble detection, Baud rate configurable
  • LoRaWAN 1.0.2 Specification
  • Software base on STM32Cube HAL drivers
  • Open source hardware / software
  • Available Band:433/868/915/920 Mhz
  • IP66 Waterproof Enclosure
  • Ultra Low Power consumption
  • AT Commands to setup parameters
  • 4000mAh Battery for Long term use
LSN50_01_Small
LG01-20

Single Channel Indoor LoRa Gateway

  • Open Source OpenWrt system
  • Low power consumption
  • Firmware upgrade via Web
  • Software upgradable via network
  • Auto-Provisioning
  • Built-in web server
  • Managed by Web GUI, SSH via LAN or WiFi
  • Support WiFi AP, Client or Ad-Hoc(Mesh) mode
  • Internet connection via LAN, WiFi, 3G or 4G
  • Failsafe design provides robustly system
  • Arduino IDE compatible. Easy to program. 
  • LoRa band available at 433/868/915/920 Mhz
  • Max range in LoRa : 5 ~ 10km

Dual Channel Indoor LoRa Gateway

  • Open Source OpenWrt system
  • Low power consumption
  • Firmware upgrade via Web
  • Software upgradable via network
  • Flexible protocol to connect to IoT servers
  • Auto-Provisioning, Built-in web server
  • Managed by Web GUI, SSH via LAN or WiFi
  • Internet connection via LAN, WiFi, 3G or 4G
  • Failsafe design provides robustly system
  • 2 x SX1276/SX1278 LoRa modules
  • Full–duplex LoRa transceiver with 2 receive channels and 1 transmit channel
  • Limited support in LoRaWAN/ Support Private LoRa protocol
  • Support upto 300 nodes
  • LoRa band available at 433/868/915/920 Mhz
  • Max range in LoRa: 5~10 km. Density Area:>500m,
LG02_20
OLG01_10

Single Channel Outdoor Gateway

  • Open Source OpenWrt system
  • Low power consumption
  • Firmware upgrade via Web
  • Software upgradable via network
  • Auto-Provisioning, Built-in web server
  • Managed by Web GUI, SSH via LAN or WiFi
  • Support WiFi AP, Client or Ad-Hoc(Mesh) mode
  • Internet connection via LAN, WiFi, 3G or 4G
  • Failsafe design provides robustly system
  • Arduino IDE compatible. Easy to program. 
  • LoRa band available at 433/868/915/920 Mhz
  • Max range in LoRa : 5 ~ 10km
  • SMA connector for external LoRa antenna
  • 12dBi WiFi directional antenna
  • Passive PoE Interface
  • Weather proof enclosure

Dual Channel Outdoor LoRa Gateway

  • Open Source OpenWrt system
  • Low power consumption
  • Firmware upgrade via Web
  • Software upgradable via network
  • Flexible protocol to connect to IoT servers
  • Auto-Provisioning, Built-in web server
  • Managed by Web GUI, SSH via LAN or WiFi
  • Internet connection via LAN, WiFi, 3G or 4G
  • Failsafe design provides robustly system
  • 2 x SX1276/SX1278 LoRa modules
  • Full–duplex LoRa transceiver
  • Two receive channels, and one transmit channel
  • Limited support in LoRaWAN/ Support Private LoRa protocol
  • Support upto 300 nodes
  • LoRa band available at 433/868/915/920 Mhz
  • Max range in LoRa: 5~10 km. Density Area:>500m
OLG01_10

LoRa Shield for Arduino

  • Compatible with 3.3v or 5v I/O Arduino Board.
  • Frequency Band: 915MHz/868 MHZ/433 MHZ (Pre-configure in factory)
  • Low power consumption
  • Compatible with Arduino Leonardo, Uno, Mega, DUE
  • External Antenna via I-Pex connector

LoRa GPS Shield for Arduino

  • Frequency Band: 868 MHZ/433 MHZ/915 MHZ(Pre-configure in factory)
  • Low power consumptionCompatible with Arduino Leonardo, Uno, Mega,Due etc.
  • LoRa™ Modem with FSK, GFSK, MSK, GMSK, LoRa™and OOK modulation
  • Preamble detection, Baud rate configurable
  • Built-in temperature sensor and low battery indicator
  • Excellent blocking immunity
  • Automatic RF Sense and CAD with ultra-fast AFC
  • Support DGPS, SBAS(WAAS/EGNOS/MSAS/GAGAN)
  • GPS automatic switching between internal patch antenna and external active antenna
  • PPS VS. NMEA can be used in time service
  • Support SDK command, Built-in LNA for better sensitivity
  • EASY™, advanced AGPS technology without external memory
  • AlwaysLocate™, an intelligent controller of periodic mode
  • GPS FLP mode, about 50% power consumption of normal mode
  • GPS support short circuit protection and antenna detection
Lora GPS Shield 30
Lora GPS Hat_10

LoRa GPS HAT for Raspberry Pi

  • Frequency Band: 868 MHZ/433 MHZ/915 MHZ(Pre-configure in factory)
  • Low power consumption
  • Compatible with Raspberry Pi 2 Model B/Raspberry Pi 3.
  • LoRa™ Modem with FSK, GFSK, MSK, GMSK, LoRa™and OOK modulation
  • Preamble detection, Baud rate configurable
  • Built-in temperature sensor and low battery indicator
  • Excellent blocking immunity
  • Automatic RF Sense and CAD with ultra-fast AFC
  • Support DGPS, SBAS(WAAS/EGNOS/MSAS/GAGAN)
  • GPS automatic switching between internal patch antenna and external active antenna
  • PPS VS. NMEA can be used in time service
  • Support SDK command, Built-in LNA for better sensitivity
  • EASY™, advanced AGPS technology without external memory
  • AlwaysLocate™, an intelligent controller of periodic mode
  • GPS FLP mode, about 50% power consumption of normal mode
  • GPS support short circuit protection and antenna detection

LoRaST IoT Module

  • STM32L072CZT6 MCU along with SX1276/78 LoRa Wireless Modem
  • Pre-load with ISP bootloader
  • I2S,I2C,LPUSART1,SPI2,USB
  • 22 x Digital I/Os, 3 x 12bit ADC; 1 x 12bit DAC
  • MCU wake up by UART or Interrupt
  • LoRa™ Modem
  • Preamble detection, Baud rate configurable
  • LoRaWAN 1.0.2 Specification
  • Software base on STM32Cube HAL drivers
  • Open source hardware / software
  • Available Band:433/868/915/920 Mhz
  • External Antenna via I-Pex 4 connector
  • Ultra Low Power consumption
  • AT Commands to setup parameters
  • Industrial standard M.2 (NGFF) interface
LoRa_Mini_Dev_1

LoRa Mini Development Board

  • Base on ATmega328P + SX1276/78
  • Frequency Band: 868 MHZ/433 MHZ/915 MHZ(Pre-configure in factory)
  • LoRa™ Modem
  • FSK, GFSK, MSK, GMSK, LoRa™and OOK modulation
  • Pre-load with Arduino Bootloader
  • Able to program via Arduino IDE

LoRa Mini Module

  • Base on ATmega328P + SX1276/78
  • Frequency Band: 868 MHZ/433 MHZ/915 MHZ(Pre-configure in factory)
  • LoRa™ Modem
  • FSK, GFSK, MSK, GMSK, LoRa™and OOK modulation
  • Pre-load with Arduino Bootloader
  • Able to program via Arduino IDE
LoRa_Mini_1
LoRa Mini Program_2

LoRa Mini Program Utility

  • Program LoRa Mini without soldering it
  • Program LoRa Mini with USB cable and Arduino IDE
  • Power on/off button
  • Reset button

LoRa I/O Controller

  • STM32L072CZT6 MCU
  • SX1276/78 LoRa Wireless Chip
  • LoRaWAN Class A & Class C protocol
  • Optional Customized LoRa Protocol
  • Bands: CN470/EU433/KR920/US915/EU868/AS923/AU915
  • AT Commands to change parameters
LT33222_40

LoRa Bee Module

  • Frequency Band: 868 MHZ/433 MHZ/915 MHZ(Pre-configure in factory)
  • LoRa™ Modem
  • FSK, GFSK, MSK, GMSK, LoRa™and OOK modulation
  • XBee form factory

Indoor LoRaWAN Pico Gateway

  • Open Source OpenWrt system
  • Managed by Web GUI, SSH via LAN or WiFi
  • Emulates 49x LoRa demodulators
  • LoRaWAN Gateway
  • SX1276 base seperate TX path
  • 10 programmable parallel demodulation paths
LG08_1 (1)

Skill Development Program

  • Faculty development programs
  • Workshops for students and faculties
  • 35 different courses available
  • Few courses are Embedded, NI LabVIEW, NI DAQ cards, Robotics etc
  • Training conducted by experienced industry experts

Sensors

  • All kind of  chemical, physics, medical etc sensors available
  • Like PIR sensor, ultrasonic sensor, gas sensor, air quality sensor, IR sensor, fire sensor, light sensor, flex sensor, heartbeat, vibration sensor, servo motor, soil moisture sensor, rain sensor
  •  Industry experts on various sensors technology to help you build your systems
sensor